Easy Search [ ? ]
 
Home  >>  Tablet  >>  Apple  >>  iPad  >>  iPad Wi-Fi (A1219)

iPad Wi-Fi (A1219)

Submitted By: powerbookmedic
Approved On: 4/5/10
Description: This is an official Powerbookmedic.com take-apart of the iPad Wi-Fi with model number A1219.

Get Adobe Flash Player
User Rating:  Please rate this video.

Comments (34):

Powerbook Medic
3 months ago
@vc - you can restore it from within the settings, general menu if you can get that far. otherwise, you can restore it after syncing it up to iTunes.
vc
3 months ago
My Ipad model: A1219 restarts every time I turn it on and select an app. I don't know what to do. please help. I only had it for a month when it started doing this. how can I reset it to factory settings if its doing that?
David Henry
6 months ago
I've done the screen replacement and it looks good - the problem is that if any camera app is started, the iPad reboots. Does anyone have any ideas?
Carol Myers
9 months ago
My problem is I put the SIM card in wrong and can't get it out. I didn't use the little bracket that was in the slot originally. Is there a tool I could purchase or do I need to take the ipad apart.
rowel
9 months ago
my ipad not funtion wil that the prrgrams shoutdown...
David Teo
11 months ago
I broke my screen doing this.
sereva
1 year ago
i have a similar problem with YAZZ. what can I do.
Powerbook Medic
1 year ago
@Mac K - it is just adhesive, so once you have the digitizer connected back, you just stick it back in.
Mac K
1 year ago
How do you put the glass & panel back on? Does it just snap back in? Do you have a re-assembly video?
Powerbook Medic
1 year ago
@dantor - probably a battery issue.
dantor
1 year ago
my ipad doesn`t charge but it`s sync the apps...what is happenin`?
YAZZ
1 year ago
MY IPAD IS DISABLED AND ASKES TO CONNECT TO ITUNES. HOW DO I PROCEED TO ENABLE IT
Powerbook Medic
1 year ago
@bashy - the video will show you how to take it apart up to the screen, then you just put it back together.
bashy
1 year ago
how to replacement the screen i pad
Powerbook Medic
2 years ago
@kk - there should be a way to skip the networking part. I'm not sure on the exact wording.
kk
2 years ago
my ipad configuration steps are not completing.. Language,Country,..etc.. when came to the Network selection its not finding.. at my home i did't have any Wi-Fi.. still its in search mode
Powerbook Medic
2 years ago
@vince - if nothing at all comes on the screen and it doesn't get detected by your computer when you try to sync it up, it is most likely the logic board.
vince
2 years ago
my ipod went blank after using it. no specific reason. can not power it again.what could be the problem? please help
Powerbook Medic
2 years ago
@Alex - the wifi and 3G models are not interchangeable.
Alex
2 years ago
What about changing logic boards from 16gb wifi to 32gb wifi + 3G is that possible assuming other parts are also upgraded such as sim card antennas etc.
francis c.n
2 years ago
well i think you guys are doing really great though i was not able to see the video but i can figure out what you guys can be up to. Keep up the good work hoping to be like you engineers someday. Cheers
Powerbook Medic
2 years ago
@Don - no, but you may need some additional adhesive.
Don
2 years ago
Do you need to replace the pads when replacing the glass and digitizer panel assembly?
Powerbook Medic
3 years ago
@Griffster - no the RAM is built onto the logic board. It is not upgradeable.
Griffster
3 years ago
Excuse me... 16GB to 64GB
Griffster
3 years ago
I did not see where the memory was... Is it possible to upgrade a 16MB version to a 64MB version?
Powerbook Medic
3 years ago
@Mike - great question, no idea. They have disappeared from every source imaginable.
Mike
3 years ago
Hi, when you'll get volume/lock/power button flex at stock?
Powerbook Medic
3 years ago
@Miguel - it is hard to say. it could be a problem with the replacement logic board or some loose connection inside somewhere. You may want to open it up and reseat all the boards and cables or take it somewhere to be professionally diagnosed.
Miguel Lopez
3 years ago
after change a iPad Main Logic Board, i swicth on the ipad and i have the itunes logo , connect itunes and i have this message there is a problem with your ipad. we´re sorry the iPad you connected may be damaged and cannot be activated for service we recommend you visit your neares apple store for more information. what can i do?¿? regards
Powerbook Medic
3 years ago
@sb - I would just go through our service parts listing to the right and see what you are missing.
sb
3 years ago
I have a ipad back case, midboard, glass and digitizer.... what other parts would i need to create a functional ipad thanks
Powerbook Medic
4 years ago
You'll need a heat gun to separate the digitizer from the midboard, but you'll have to be careful as those home buttons are easily susceptible to melting.
Bryan
4 years ago
Have you tried using a heat gun to loosen the adhesive connecting the LCD to the Digitizer?
Collapse comments


If you would like to leave a comment about the video, please type in your name and comment below.

You must have cookies and javascript enabled to submit comments

Name:
Comment:


Service Parts
Tools
Our Price: $7.95
Price Starts at: $14.95
Our Price: $79.95
Price Starts at: $59.46
Our Price: $6.97
Our Price: $69.95
Our Price: $19.47
Our Price: $1.02
Price Starts at: $17.96
Our Price: $1.13
Our Price: $8.46
Our Price: $0.95
Our Price: $1.72
Our Price: $3.95
Our Price: $7.95
Our Price: $4.95
Our Price: $9.95
Our Price: $4.21
Our Price: $5.46
Price Starts at: $49.95
Our Price: $3.79
Our Price: $19.95
Our Price: $1.00
Our Price: $0.72
Our Price: $9.95
Our Price: $2.80
Our Price: $2.74
Our Price: $94.05
Our Price: $103.96
Our Price: $149.95
Our Price: $85.65
Our Price: $5.46
Our Price: $1.44
Our Price: $1.23
Our Price: $1.00
Our Price: $149.95
Our Price: $4.95
Our Price: $2.95
Our Price: $1.13
Our Price: $0.95